Tractor Parts Inc. Is dedicated to supplying you with all of your farm tractor parts, tractor decal, tractor manual, and accessory needs. Tractor Parts Inc. Has a large selection of tractor parts for all makes and models of tractors including Ford tractor parts, and Massey Ferguson tractor parts. We also carry parts for all major brands of tractors and implements such as John Deere, Allis Chalmers, International Harvester, Kubota tractors and more.We also have the web's largest selection of replacement tractor decals. Our tractor decals are high quality replacement decals that are as close to the original tractor decals as possible without purchasing them from an OEM tractor dealership.
12 Volt Conversion Kit For Ford 8n found in: Alternator Conversion Kit, Electronic Ignition Conversion Kit 12 Volt Negative Ground System, Electronic Ignition Conversion Kit, 12 volt negative ground system, Ammeter (Amp). Restore your Redbelly tractor with premium parts. Browse our Hydraulic Lift and Related Parts for grommets, stabilizer bars, pump drive hubs & more!
We are confident that you will be very impressed with our tractor decals. We also have replacement tractor seats for many models as well. We offer many hard to find replacement tractor seats and cushions. We offer high quality original style tractor seating as well as lower cost aftermarket versions of tractor seats.If it does not fit, if you don't like the way it looks, or if it is unused, we take it back, we refund your money and there is no restocking fee. This return policy does not apply to glass or seat orders, for which there is a 20% restocking fee.
We will not accept returns without a Return Materials Authorization Number (RMA#). Please call (888)470-7395 to obtain an RMA#. In the event of damage, shortage, or any error on any shipment, please contact us immediately via phone or email at [email protected] for instructions. Please save all the original packaging!
We will not accept returns of orders older than 6 months.Our company wants to be your one stop online source for tractor parts. Whether you need water pumps, radiators, steering parts, hydraulic parts, or tractor rims; Tractor Parts Inc. Has the part you need from the front of your tractor to the rear. If there is an item you need that you do not see on our tractor parts site, please email us or call us with the item you need.
![]()
There are many more tractor parts that will be added to the Tractor Parts Inc. Website in the near future.
Tractor Parts Inc. Has many tractor parts available for your tractor and implements. If you happen to be the proud owner of a classic Ford tractor, be sure to visit our partner site FordTractorPart.com. FordTractorPart.com is a site that is strictly dedicated to supplying tractor parts, literature, and accessories for the Ford 8N tractor as well as all pre 1964 model Ford tractors. For a detailed selection of Ford and New Holland tractor parts, go to our Ford tractor website Fordtractorpart.com.We have the parts for your tractor and can ship to all states.
Order the manual or parts you need online and have your order shipped anywhere! We keep our warehouse stocked with parts for Allis Chalmers, Case, Ford, International Harvester / Farmall, John Deere, Massey Ferguson, Massey Harris, Minneapolis Moline, Oliver and White. Search our store and you will find low prices on everything from tractor seats, manifolds, radiators, decals, carburetors, gauges, rims, steering wheels to tractor hoods, fuel tanks and tractor lights. We also carry parts service and operator manuals for many makes of tractors. We are adding multiple replacement parts for farm implements as well including Bush Hog and New Idea hay cutting parts.Tradenames and Trademarks referred to on Tractor Parts Inc.
Products and within the Tractor Parts Inc. Websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Tractor Parts Inc., our products, or our website nor are we sponsored by them.
John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
This 9 inch Clutch Kit contains 10 spline spring drive disc part number NAA7550A, 9 inch single pressure plate part number 8N7563, pilot bearing part number C5NN7600A, release bearing part number C0NN7580A and alignment tool. This clutch kit is for tractor models 1800, 1801, 2000 (4 cylinder 1962-1964), 2031, 2110TR, 2120, 2130, 2131, 4000 (4 cylinder 1962-1964), 4031, 4110TR, 4120, 4121, 4130, 4131, 4140, 501, 600, 601, 700, 701, 800, 801, 900, 901, 2N, 8N, 9N, NAA, NAB. (Part No: 8N7563K)$95.88. This is a Replacement High Quality Radiator.
It is not exactly like original but will replace the original with no modification required (except if using a fan shroud). For 8N, 9N, 2N. Copper Core, 3 rows of tubes, weight 16 lbs. Drain cock included. 1 year warranty. DOES NOT COME WITH CAP.
The Original or Replacement Fan Shroud will not fit this radiator without some modification to the fan shroud. This modification consists of trimming the inside of the bottom of the fan shroud. This is a replacement radiator for OEM part number 8N8005. (Part No: 8N8005)$171.12. This radiator hose clamp is an EXACT reproduction of the ORIGINAL hose clamp. This radiator hose clamp is for tractor models 8N, 9N, 2N (1939 to 1954), NAA, Jubilee (2 per tractor, 1953 to 1954). For 1 3/4 inch to 2 inch outside diameter hoses.
![]()
Also works on other Ford 4 Cylinder tractors through 1964. Replaces ``608287. PLEASE NOTE: Original hoses are usually thicker than current hoses available for many antique tractors. Measure your current outside diameter to ensure fit. You can add electrical tape to the ends to have these original style clamps effectively tighten on newer (thinner) hoses. (Part No: 608287)$3.75.
This gear shift lever with knob replaces NAA7209A and 8N7209C shift levers. This newer version has 5/16 inch UNF thread for the shift knob (knob included). The early series 3/8 inch knob thread shaft is no longer available. Note: use gear shift knob C5NN7213A (included) if you need a replacement. This gear shift lever fits tractor with single lever 4 speed or torque converter transmission: 2000, 2110LCG, 3000, 340, 3400, 340A, 3500, 3550, 4000, 420, 445, 4500, 532, 535, 540, 540A, 545, 5500, 600, 601, 700, 701, 800, 801, 8N, 900, 901, Jubilee, NAA (Part No: C5NN7202B)$77.21. For tractor models 9N, 2N and 8N with 3 and 4 speed transmissions (1939-1952).
Will also work for Jubilee except for the transmission to rear end gasket. This transmission bearing and seal kit contains seals, bearings and gaskets required for transmission rebuild. Contains (2) 9N7086, (1) 9N4662, (1) D5NN7223A, (1) 9N7223B, (1) 8N7052A, (1) 15385-TIM, (4) 25877, (4) 25820-TIM. Replaces: 9N7066, 86516471, 9N7086, 9N7086A, 9N7086GV, 9N7120, 9N7120GV, 81804773, 8N7052A, 8N7052A2, C0NN7052A, 83945495, 9N7067, 9N7067GV, 517512, 241336, 605188, 9605470, 9N4662, 9N4662GV, 9N7223, 9N7223B, 8N7223, D5NN7223A, E6NN7223BA, 83958318, 81817212. (Part No: TSBK3952)$151.717Electrical System. Complete Electronic Ignition Conversion Kit by Pertronix to convert your tractor to an electronic automotive type coil system. For 8N, 9N, 2N with FRONT MOUNT Distributor only.
For tractors with 6-volt positive ground only. This electronic module replaces your points and condenser, also includes 40, 000 volt coil, coil clamp, coil wire and distributor cap. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy. For tractors with 6-volt positive ground only. (Part No: 1247XTP6)$225.11.
Complete Electronic Ignition Conversion Kit by Pertronix to convert your tractor to an electronic automotive type coil system. For 8N, 9N, 2N with FRONT MOUNT Distributor only. For tractors with 12-volt negative ground only. This electronic module replaces your points and condenser, also includes 40, 000 volt coil, coil clamp, coil wire and distributor cap. Never change points again! Easy installation, no complicated wiring, fits entirely inside distributor.
Increases spark plug life and horsepower, improves fuel economy. For tractors with 12-volt negative ground only. (Part No: 1247XT)$214.92. Pertronix Electronic Ignition kit for the following tractors using 4-cylinder gas engine: 8N (using side mount distributor), NAA, Jubilee, (501, 600, 620, 630, 640, 650, 660, 601, 611, 621, 631, 641, 651, 661, 671, 681, 700, 800, 900, Series), 2000. And for the following tractors using 172 4-cylinder gas engine: 800, 900, 801, 901, 4000. This electronic module by Pertronix replaces your points and condenser. Never change points again!
Easy installation, no complicated wiring, fits entirely inside distributor. Increases spark plug life and horsepower, improves fuel economy.
For tractors with 12-volt negative ground only. (Part No: 1244A)$106.75. 120 CID 4 cylinder gas 3-3/16 inch standard bore. Engine Overhaul Kit contains, thin wall.040 inch sleeves, 4 ring pistons, rings, pin and retainers, pin bushings, complete gasket kit, intake and exhaust valves, valve springs and retainers, guides and retainers, valve keys. For 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately.
If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category.
(Part No: EOK102-LCB)$312.85. 120 CID 4 cylinder gas 3-3/16 inch standard bore. Engine Overhaul Kit contains, thick wall.090 inch sleeves, 3 ring pistons, rings, pin and retainers, pin bushings, complete gasket set, intake and exhaust valves, valve springs and retainers, guides and retainers, valve keys. For 8N, 9N, 2N. NOTE: Please indicate in comments if you have rotating valves, (4) 8N6505C and (4) 8N6534B will be added to the order for an additional special price of $85.00. IF ORDERING ON-LINE, THIS ADDITIONAL CHARGE WILL BE ADDED TO YOUR ORDER AFTER YOUR RECEIPT IS PRINTED. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves.
If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: EOK106-LCB)$355.35- TO DETERMINE WHICH OF THE BELOW KITS YOU WILL NEED, YOU NEED TO KNOW THE FOLLOWING: (1) If your pistons have 3 or 4 rings per piston. (2) If your piston sleeve thickness is.040 or.090 inches. (3) If your oil pump gear is 3/4 or 9/16 inches wide.
(4) If you have rotating or non-rotating exhaust valves - If your keepers or keys on the exhaust and intake valves are the same, you DO NOT have rotating valves. If your keepers or keys on the exhaust and intake valves are the different, you DO have rotating valves.
Engine bearings can be ordered from our ENGINE BEARINGS category.NOTE. 3 RING PISTONS,.090 INCH SLEEVES, 3/4 OIL PUMP GEAR WIDTH. Complete Engine Kit. Contains, thick wall.090 inch sleeves, 3 ring pistons, rings, pins and retainers, pin bushings, complete gasket set, timing gear, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, points and condenser, spark plugs, oil filter, basic carb kit.
For tractor models 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category.
(Part No: 3-8H-LCB)$441.60. 120 CID 4 cylinder gas 3-3/16 inch standard bore, 3/4 inch oil pump gear width. Complete Engine Kit contains, thin wall.040 inch sleeves, 3 ring pistons, rings, pins and retainers, pin bushings, complete gasket kit, timing gear, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, points and condenser, spark plugs, oil filter, basic carb kit. For tractor models 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly.
These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-8T-LCB)$455.40. 120 CID 4 cylinder gas 3-3/16 inch standard bore, 9/16 inch oil pump gear width. Complete Engine Kit contains, thick wall.090 inch sleeves, 3 ring pistons, rings, pins and retainers, pin bushings, complete gasket kit, timing gear, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, points and condenser, spark plugs, oil filter, basic carb kit.
For, 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves.
If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 3-9H-LCB)$412.01. 120 CID 4 cylinder gas 3-3/16 inch standard bore, 9/16 inch gear width.
Complete Engine Kit contains, thin wall.040 inch sleeves, 4 ring pistons, rings, pins and retainers, pin bushings, complete gasket kit, timing gear, intake and exhaust valves, springs, spring retainers, guides, guide retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, fan belt, point and condenser, spark plugs, oil filter, basic carburetor kit. For 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately. If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category.
(Part No: 4-9T-LCB)$431.21. 4 RING PISTONS,.090 INCH SLEEVES, 9/16 INCH OIL PUMP GEAR WIDTH. Complete Engine Kit contains, thick wall.090 inch sleeves, 4 ring pistons, rings, pins and retainers, pin bushings, complete gasket kit, intake and exhaust valves, springs, spring retainers, guides, retainers and seals, valve keys, upper and lower radiator hose, air cleaner hose, oil pump kit, timing gear, fan belt, points and condenser, spark plugs, oil filter, basic carb kit. For, 8N, 9N, 2N. NOTE: If you have rotating valves you will also need 4 x 8N6505C exhaust valves and 4 x 8N6534B Valve Rotor Assembly. These are sold separately.
If your keepers or keys on the exhaust or intake valves are the same, you DO NOT have rotating valves. If they are different then you DO. Bearings not included, they can be ordered separately from our Engine Bearings category. (Part No: 4-9H-LCB)$480.86. Horizontal Muffler and Pipe, one piece welded assembly. For 8N, 9N, 2N with under-hood exhaust.
WELDED 1 PIECE ASSEMBLY; MUFFLER AND EXHAUST PIPE INLET LENGTH 2 1/2 inches, INLET INSIDE DIAMETER 1 1/2 inches, SHELL LENGTH 23 INCHES, SHELL DIAMETER 3-1/4 INCHES, OUTLET LENGTH 8 1/2 INCHES, OUTLET OUTSIDE DIAMETER 1 1/2 INCHES. OVERALL LENGTH 53 INCHES, EXHAUST PIPE: FLARED INLET VERTICAL LENGTH 15 1/2 INCHES, HORIZONTAL LENGTH 22 INCHES, OUTLET OUTSIDE DIAMETER 1 1/2 INCHES. (Part No: 8N5230)$26.04. Use to install temperature gauge in tractors that did not originally come with temp gauge. Kit includes original style hose clamps, temp gauge adapter pipe and temperature gauge.
Installs in upper hose. Cut hose, slide new adapter pipe in place, drill 2 inch outside diameter hole in dash to mount gauge. For tractor models: 2N, 8N, 9N. The temperature gauge is a complete assembly with bracket and adapters. Dial calibrated to 280 degrees, extra long 70 inches capillary line. (Part No: FDTEMP)$77.07Hitch / Drawbar.
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |